Pages

Church Pages

Fav Blogs

Saturday, September 30, 2023

Quilt Shot Block 159~ Needlework Sept 2023 Meeting

 
1.5 inch hexies hand pieced with 3D leaves.

These very old quilts of maybe 1920s
 where passed on from one member to another.
The history of these quilts is not known.
There was no batting. 
Only seemed to be made with a lightweight backing.
Perhaps made to be a summer quilt?


Tuesday, September 26, 2023

Tues Tutorial~ Welcome Yard Flag

 My church needed Welcome Flags to replace the sun faded flags we had. I made 2 flags and they both were  free because they were made from scraps people had given me, or I had leftover from another project.
 
 
 
 
 
 
 
 
 
******************
Tuesday Tutorial
******************
I started by raw edge piecing the background with scraps. The method that is similar to my Bottom of the Barrel Tag Making. I just overlap the fabrics and stitched. 
A 20x16 inch backing for flag was cut from some broadcloth curtain type fabric. I have a roll of it I bought years ago. The wrong side shows mostly white which is the side I have to appear on the back.  
The backing was then used as a pattern to trim the collage piece to size.
I start free hand cutting my letters by deciding the height and width they should be to put the wording across the flag. In this case I decided on 3.5 x 3 inches pieces of fabric to cut letters. I did a double cut to make shadowed letters as I did on THIS flag. The back of these red pieces of fabric have light weight iron on interfacing.
I still had to do some artistic maneuvering and cutting to make them all fit.
Then the leaves. These were pieces from another flag so they aren't duplicates. I did trim the backgrounds after I stitched.
Raw edge stitch around all pieces.
Only need to stitch around top layer of letters.
Place the front and back pieces right sides together,
and stitch across what will be the top of the flag.
 To make the pole channel:
Unfold.
Press open seam.
Mark as shown above.
2 inches from each side of seam
Then cut in 1/2 inch.
Turn 1/4 inch, press
Turn another 1/4 inch
Pin if need
Stitch along folded edge as shown below.
 
Turn rights sides together.
 Pin all around except for the area turned under.
The turned under area is the opening for the flag rod.
Do not pin about a 6 inch opening across the bottom.
You will NOT stitch in this 6 inch area.
The flag pole opening is not large enough to turn inside out.
I put double pins to remind me where not to stitch.
Turn the piece inside out through the 6 inch opening.
To finish making pole channel,
top stitch across 2 inches down from the top edge.
 
Top stitch 1/4 inch from edge 
Across the top
All around flag from bottom of pole channel opening
the the bottom of the channel on the other side. 
Being sure to turn under the edge of the 6 inch opening.
The top stitching will close the 6 inch opening.
Then your flag is ready to hang.
Surrounding the flag
you see the greenery that Mr. G planted a few years back.
He does live on, even at church.

Another flag made with a different leaf design
which I do like better.
So get your scraps out and make a FREE yard flag.
 
***************************
Shared @
 Grammy's Grid- Thanks for the feature on #26!
 

 






 



Friday, September 22, 2023

Fun Fri~ A Forgotten Card

 

A card I made July, 2022 and forgot to share.
It was a thank-you card to my sister
for making Memorial Day Flower arrangements 
for our parents and brother's grave. 
It's been one of my most favorite cards.

Tuesday, September 19, 2023

Tues Tutorial~ Serger Shirt Memory Pillow

 I was asked to make more Shirt Memory Pillows.  However, these were not shirts but rather tshirts, sweat shirts and sweaters.  I used the serger to make these. In this tutorial there are some serger tips.
 
 
 

 
 
*****************
Tuesday Tutorial
******************
Work laid out. Not all could be used because of location of stones and very loose weave, or too short.
A slotted ruler that measured 16 inches
 on each outer edge was used.
 




 Back

Front

Lay back piece right side
to front piece.

Tip 1: to sew knits

set Differential Feed
to about 1.50.

Tip 2: To turn a corner
when you come to the corner
Raise both needles by
 turning knob on right of machine
toward you (never back)
(see picture 3 pictures above)
Needles up allow you to pull the threads just a bit
to allow them to be loosened.

Lift the pressure foot.
Pull slightly on the fabric
and turn.
The slight loosening of threads
allows you to turn the piece under the foot.
After you put the pressure foot down,
continue to sew.


Turn inside out through the opening
made by overlapping the back.



 Shared @
 
Featured @  !!!!!!